What a Tonne of Steam Costs on Husk, Coal, Briquettes, Oil, Gas and Power
How to work out the fuel cost of a tonne of steam for rice husk, wood, briquettes, coal, furnace oil, diesel, PNG, LPG and electricity, with a worked table.
4 min read
By the Yantra Boilers team

Key takeaways
- The fuel cost of steam is heat per tonne of steam divided by the fuel's calorific value and the boiler's efficiency, times the fuel's price.
- At 10.54 kg/cm² with 60 °C feed water, a tonne of steam needs about 6,04,400 kcal.
- Solid biomass and coal usually make the cheapest steam; oil, gas and electricity cost more per tonne but less in handling and emissions control.
- Use your own fuel prices and test reports: the prices in the table are examples to show the method, not market rates.
When a plant chooses between a husk fired boiler and a gas fired one, the boiler’s price is only the start. Over its life, the fuel costs many times what the boiler did. The comparison buyers need is simple to make once the method is clear: what does each fuel cost to make one tonne of steam?
The method
- Heat in a tonne of steam: 1,000 kg × (enthalpy of steam at the working pressure − enthalpy of the feed water). At 10.54 kg/cm² (g) and 60 °C feed water that is about 1,000 × 604.4 = 6,04,400 kcal.
- Fuel needed: that heat ÷ (the fuel’s gross calorific value × the boiler’s efficiency on that fuel).
- Fuel cost: fuel needed × the fuel’s price per unit.
A worked table
| Fuel | GCV (kcal per unit) | Efficiency | Fuel per tonne of steam | Example price (₹ per unit) | Fuel cost per tonne of steam |
|---|---|---|---|---|---|
| Rice husk | 3,200 per kg | 72% | 262 kg | 5 | ₹1,312 |
| Wood | 3,000 per kg | 70% | 288 kg | 6 | ₹1,727 |
| Biomass briquettes | 4,000 per kg | 74% | 204 kg | 8 | ₹1,634 |
| Indian coal | 4,000 per kg | 76% | 199 kg | 9 | ₹1,789 |
| Imported coal | 5,500 per kg | 80% | 137 kg | 12 | ₹1,648 |
| Furnace oil | 9,700 per litre | 86% | 72 litres | 55 | ₹3,985 |
| Diesel | 9,000 per litre | 87% | 77 litres | 90 | ₹6,947 |
| Natural gas (PNG) | 9,000 per SCM | 88% | 76 SCM | 50 | ₹3,816 |
| LPG | 11,900 per kg | 88% | 58 kg | 95 | ₹5,483 |
| Electricity | 860 per kWh | 98% | 717 kWh | 8 | ₹5,737 |
Reading the table
On these example prices, biomass and coal make steam at well under half the cost of oil, gas or electricity. That is why rice mills, plywood units and many food processors run on husk, wood or briquettes. But fuel cost per tonne is not the whole picture:
- Handling. Solid fuels need storage, feeding, ash removal and labour; gas and power need almost none.
- Emissions. Solid fuel boilers need dust collection, such as cyclones, bag filters or scrubbers, to meet the limits in your area.
- Availability. A cheap fuel that is unavailable for two months a year is not cheap. Many plants choose multi-fuel boilers for this reason.
- Turndown. Gas and oil burners follow a swinging load easily; a solid fuel bed takes longer to respond.
From per tonne to per year
Multiply the cost per tonne by the tonnes made in a year. A 2 TPH boiler averaging 1.5 TPH for 6,000 hours makes 9,000 tonnes a year. At the example husk figure that is about ₹1.18 crore of fuel; at the example diesel figure, about ₹6.25 crore. Small differences in efficiency are worth a great deal at that scale, which is why maintenance and a clean boiler pay for themselves.
Ways to cut the cost of steam
- Return condensate. Hot condensate back to the feed tank raises the feed water temperature and cuts the heat each kilogram of steam needs.
- Control blow-down. Blow down on water quality, not by habit; every unnecessary blow-down throws away hot, treated water.
- Keep heating surfaces clean. Soot on the gas side and scale on the water side both push up flue gas temperature and fuel use.
- Keep solid fuel dry. Wet husk or wood spends its own heat boiling off water before it heats yours.
- Fix steam traps and insulation. A failed trap or bare pipe loses steam the boiler has already paid for.
- Add an economiser. Recovering heat from the flue gas into the feed water often pays back quickly on a boiler that runs long hours.
Comparing two offers on fuel cost
When two makers quote boilers of the same capacity, compare the efficiency each offer states, on the same calorific basis, for the fuel you will actually burn. A few points of efficiency on a boiler that makes thousands of tonnes of steam a year is worth more than a small difference in price, so ask for it in writing in the technical particulars.

A more expensive fuel can still make sense: where solid fuel handling and ash disposal are impractical, where emissions limits are tight, or where the load is small and intermittent and a gas or electric boiler can start and stop in minutes.
Working it out for your own plant
- Find your working pressure and feed water temperature, and read the steam's enthalpy from a steam table; subtract the feed water's.
- Get the calorific value of your fuel from a recent test report; if you buy from several suppliers, use the average and note the spread.
- Use the efficiency your boiler actually achieves, from a combustion test or from steam made against fuel burned over a week, not the brochure figure.
- Use the price you paid per unit delivered to your gate, including transport and handling.
- Multiply out, and check the answer against your real fuel bill and steam use for a month. If they disagree by much, one of the inputs is wrong.
Done this way, the cost of steam becomes a number the plant can track month by month. A rise with no change in fuel price is the earliest sign that a boiler needs cleaning, that traps are failing or that the fuel has got wetter, long before anyone notices on the floor.
Frequently asked questions
- Which fuel makes the cheapest steam?
- It depends on local prices, but solid biomass such as rice husk, wood and briquettes, and coal, usually make the cheapest steam in India, with more handling and emissions control than oil, gas or electricity.
- Why do efficiencies differ by fuel?
- Moisture, ash and how completely the fuel burns all change how much of its heat reaches the steam. Wet biomass loses more heat in the flue gas than dry gas or oil.
- Should I use gross or net calorific value?
- Be consistent. This guide uses gross calorific value with efficiencies stated on the same basis, which is common practice for Indian boilers.


